Stirrer Accessories
Chemglass Life Sciences Support, Stirrer Stand
Support, Stirrer Stand. Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep overall and has a black enamel finish. Support rod is .625” (16mm) diameter x 30” long.
Cole-Parmer Industrial Mixer Lift Stand, Winch; 42-82" Height
These new heavy-duty mixer stands are constructed from heavy gauge steel and square steel tubing to accommodate loads of up to 200 lbs. Use with any of our clamp mount mixers. Stands allow you to easily raise or lower your mixer into drums or tanks up to 48" in diameter. Each stand includes a 12" square base plate with four 9/16" mounting holes for permanent attachment to floors or dollies. Use the manual stand for lighter mixers. Manual stand lets you move mixer up or down in 1" increments; clevis pin holds the mixer in place. The winch stand is ideal for heavier mixers. Raise the mixer to any height; winch holds the mixer in place. Choose the air-powered stand for your heaviest mixers. Air motor holds mixer in place at any level.
Cole-Parmer Caframo Collapsible blade impeller; 3-1/2" dia (Stainless Steel)
Choose the impeller compatible with your mixer and to suit your mixing needs.
Med Vet International 3.5mm x 18mm Titanium Cortical Self-Tapping Screws, J1074BT, 6-Pack
Many fractures in feline and small canine patients are too small for the 2.0mm DCP and the 2.7mm CDP is too large.The difference between these plates is enormous compared to the difference between 2.7 and 3.5 CDPs. The AMI (resistance to bending) of the 2.7 CDP is 20 times stiffer than the 2.0 DCP. The AMI of the 2.4 DCP is 10 times that of the 2.0 DCP.The solution is a 2.4 series of plates and screws. The plates in both size and strength are midway between 2.0 and 2.7 DCPs. The range and specifications are shown below. The standard 1.5mm hex screwdriver (used for 1.5 and 2.0 screws) is required. The pilot drill is 1.8mm and dedicated instrumentation such as load/neutral guides are also available.
Ace Glass, Inc. PTFE agitator, (4) 140mm anchor style blades, fits 28mmdrilled shafts. Replacement nut & bolt: 8091-134
AGITATOR PTFE 28MM 140MM BLADE
Chemglass Life Sciences Stirrer Blade, PTFE, Banana Shape, Solid, 10mm, for 3000mL Flasks, 40/50 minimum joint clearance
Stirrer Blade, PTFE, Banana Shape, Solid, 10mm, for 3000mL Flasks, 40/50 minimum joint clearance. Blade is shaped to resemble the contour of a round bottom flask. Blades are solid. Made of 1/8" PTFE to fit 10mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.
Chemglass Life Sciences PFA Coated Hastelloy C-276 Thermocouple: 1/4" Diameter x 32" Long, Type "K", Fits Reactor Capacity: 30L & 50L Short
PFA Coated Hastelloy C-276 Thermocouple: 1/4" Diameter x 32" Long, Type "K", Fits Reactor Capacity: 30L & 50L Short. Thermocouples for use with Chemglass process reactors. Available in both ¿T¿ (blue connections) and ¿K¿ (yellow connections). The detachable thermocouples are for direct insertion in the reactors using a CG-1048-A or CG-1042-E thermocouple adapter, while the 4¿ long Hastelloy C-276 style is for use with the CG-1971 baffles and adapters. Detachable type thermocouples have a standard male plug (OST) and require a coiled extension cord for connection to the CG-3498 temperature monitor. The 4¿ long Hastelloy C-276 thermocouples are supplied with a 4ft FEP insulated cord having a standard male plug (OST).PLEASE NOTE: THE 1/2¿ DIAMETER PROBES HAVE A TRANSITION TO 6¿ OF PTFE LEADS AND ARE CLEAR FEP PTFE COATED.Maximum Probe Temperature Based on Coating- FEP is 200¿C and the Black PFA is 250¿C